How to Fix a Windows 10 Automatic Repair Loop 2021.
A bad system update. A new graphics card Or corrupted system files. Even a new USB mouse can all cause Windows 10’s terrible auto-repair cycle. When you try to boot your Windows computer.
You usually see this error when Windows 10 tries to boot and fails. Forcing itself to go through an endless cycle of auto-repair attempts. If Windows cannot recover itself. It reboots and repeats the cycle. Here’s what you need to do to fix the Windows 10 automatic repair cycle.
What Causes a Windows 10 Automatic Repair Loop?
There is no single reason for Windows 10 automatic recovery, but there are several situations that can trigger it. Missing or corrupted system files are one of the most common reasons Windows cannot boot (or repair itself) because these critical files that it needs to run are not available.
This prevents the Windows kernel (ntoskrnl.exe) and other critical Windows services from fully loading, preventing you from using your computer. Another issue that can cause a repair cycle is a recently installed component or a connected peripheral that is missing a device driver (or just doesn’t work correctly).
If you’ve recently updated your computer, your new components will need device drivers for Windows to use it. If drivers are missing, out of date, or not supported, this can cause a recovery cycle, especially for critical components such as a new graphics card.
Other issues such as faulty components, malware infection, corrupted system registry, and even corrupted installation files point to a possible cause. Fortunately, many of the fixes you can try below will work for most causes of the Windows 10 automatic repair cycle.
1. Disconnect or Remove Recently Installed or Connected Devices
If you recently installed new hardware prior to the Windows 10 auto-repair cycle, then the hardware you installed is likely the cause of the problem.
This usually happens due to a missing driver or a driver conflict. Device drivers enable Windows to communicate between hardware (such as a video card) and software (Windows services and third-party software). If the drivers are missing or broken, it can prevent Windows from loading properly.
In most cases, removing the problematic device will allow Windows to skip the problem. If Windows boots with a remote device, you can install new drivers or replace a component. For example, installing a new graphics card may require downloading and installing drivers from the manufacturer’s website.
2. Run System Repair Tools (Chkdsk, SFC)
If you can’t immediately track down the root cause of the Windows 10 automatic recovery loop, it’s best to start with some common system recovery tools. Although Windows will not boot, you can usually force Windows to boot from a command prompt window using the Advanced Options menu screen.
- To do this, restart your computer and press the F8 key on your keyboard until the Windows logo and spinning icon appear (you may need to repeat this step several times). This should bring up the Windows boot troubleshooter menu. To get started, select “View advanced recovery options”.
- From the Select Option menu, choose the Troubleshoot option.
- From the Troubleshoot menu, select the Advanced Options option.
- Choose Command Prompt from the Advanced Options menu to load a minimal version of Windows that displays only the Command Prompt window.
- In a Command Prompt window, enter chkdsk / r c: to start a low-level error check on the system disk using the Check Disk utility. If errors are found, chkdsk will automatically fix them (if possible).
- You can then check the integrity of your Windows system files using the System File Checker tool. To start, enter sfc / scannow. This may take some time.
- When finished, click the cross (X) in the upper right corner to close the Command Prompt window and restart your computer.
3. Run the Windows 10 DISM tool
The System File Checker utility above will fix the system files using a local Windows image. If certain files become corrupted, Windows will replace them locally, but if the image itself was corrupted, Windows cannot recover itself.
To overcome this, you can use the Deployment Image Servicing and Management (DISM) tool to restore system files first.
- To do this, press F8 during boot, then select See more repair options.
- From the boot troubleshooter menu, select Troubleshoot> Advanced options> Startup options> Restart.
- In the next step, select “Enable Safe Mode with Loading Network Drivers” by pressing number 5 (or F5) on your keyboard. Windows will boot into Safe Mode with only minimal services enabled.
- After Windows boots in Safe Mode, right-click the Start menu and select Windows PowerShell (Admin).
- In the PowerShell window, enter DISM / Online / Cleanup-Image / RestoreHealth and wait for the process to complete, which may take a while.
- When the DISM tool finishes, restart your computer and follow the above boot steps in a Command Prompt window, repeating the SFC command (sfc / scannow) to ensure that Windows is fully restored. …
4. Disable Automatic Startup Repair to Limit Boot Loops
If you are confident that the Windows 10 installation is still working, then you can turn off Automatic Startup Repair. This should allow you to boot into Windows without the need for recovery.
However, this will only work if Windows is working properly. If this is not the case (and you still cannot boot), you may need to consider more drastic fixes (such as Windows Restore) afterwards.
- First press F8 and wait for the boot troubleshooter to load by selecting View Advanced Recovery to continue.
- From the boot troubleshooter menu, select Troubleshoot> Advanced Options> Command Prompt, then wait for the Command Prompt window to open. You may need to authenticate with your local account password or Microsoft account first.
Maintaining a Healthy Windows 10 Installation
If Windows 10 is still in an automatic repair cycle (or if it has other issues preventing it from booting properly). You may need to consider more radical recovery methods, such as cleaning and reinstalling Windows. This can result in the loss of locally saved files, so be sure to back up your hard drive before starting.
After you manage to fix the recovery cycle by following the steps above. You will need to ensure a smooth installation with regular system maintenance. It is very important to keep Windows up to date with device driver updates and important system updates.
If updates get stuck or updates just don’t install properly, be sure to try a few simple fixes, from a quick restart to running the Windows Update troubleshooter. However, updating isn’t the only thing you can do to improve your PC’s performance – even cleaning your PC will have a positive effect.
-
- In the Command Prompt window, enter bcdedit and double-check the ID and recovery enabled values. The identifier value is usually displayed as {default} and recovery enabled is specified as yes.To change this, enter bcdedit / set {default} recoveryenabled no to disable automatic boot recovery.
If you run this command from a command prompt or a PowerShell window in safe mode, you may need to replace the id value with {current} (for example, bcdedit / set {current} recovery enabled no).
- In the Command Prompt window, enter bcdedit and double-check the ID and recovery enabled values. The identifier value is usually displayed as {default} and recovery enabled is specified as yes.To change this, enter bcdedit / set {default} recoveryenabled no to disable automatic boot recovery.
-
- Click the cross (X) in the upper right corner to restart your computer. If Windows can boot, in the next step you will be able to log in as usual.
How to Fix a Windows 10 Automatic Repair Loop 2021
How to Fix a Windows 10 Automatic Repair Loop 2021
- Click the cross (X) in the upper right corner to restart your computer. If Windows can boot, in the next step you will be able to log in as usual.